Hari ini GEMS memiliki desain dan manufaktur portofolio luas di liquid level, flow switch dan pressure switch, sensor dan transduser, solenoid valve, dan pre-assembled fluidic system. Gems adalah divisi dari Danaher, 500 perusahaan di dunia. Gems Sensors Control memiliki fasilitas manufaktur di Amerika Utara, Eropa, dan Asia dan mendukung penjualan, teknik dan kantor pelayanan di seluruh dunia. Gems memiliki support mendukung desain dan manufaktur Anda.

Warrick Conductivity Sensors

Warrick Conductivity Sensors Image

Warrick® Conductivity level control systems rely on the liquid level sensing capability of probes (electrodes) that are housed inside fittings designed to accommodate one or more probes. The concept is simple: take advantage of a liquid’s conductive properties to complete a circuit and cause a control relay to actuate. These single- or multi-point sensors have no moving parts and the stainless steel corrosion-resistant electrodes can be cut to the desired length. Multiple probes per fitting allow control of several functions in less space with less expense for equipment and installation. To create a system select from numerous level controls, fittings and probe options. For OEM’s we also have the capability to custom configure liquid level control sensors and electrode fittings to meet your specific conductivity level control application requirements.

Warrick® Liquid Level Controllers

For over 50 years Warrick® Controls have offered dependable no-moving-parts control and monitoring of conductive liquids. Now as part of the Gems™ Sensors family, Warrick® conductivity controls continue to offer reliability, process automation, labor savings, flexibility and operator safety at economical cost. The concept is simple: take advantage of a liquid’s conductive properties to complete a circuit and cause a control relay to actuate. Use of permanently-mounted stationary electrodes gives the user precise accuracy, repeatability and no-moving-parts reliability. This simple concept has led to the development of a complete line of conductivity-based liquid level detectors, water level detectors, and control units and electrode fittings shown here. For OEM’s we also have the capability to custom configure liquid level control units and electrode fittings to meet your specific application requirements.

System Components

  1. The liquid level control unit is an electrical device with contacts that open and close in response to liquid levels sensed by the probes. Because it is wired directly to the power source and to the sensing source, it can send signals that activate or de-activate solenoids, pumps, alarms or pressure switch devices. Warrick®controls are available in many different designs and sensitivity ratings for a wide range of application requirements.
  2. The fitting is a housing that holds the probes (or floats), insulates them from the vessel, and provides a means of connection to the control. Warrick® fittings are available for single-probe or multi-probe applications, for mounting to vessels in a variety of ways, and in open or pressure tight styles.
  3. The probe is a sensor that extends downward from the fitting, with the tip positioned precisely at the level where the control should be activated. Warrick® probes are available in a variety of materials to suit different liquids and a variety of lengths to fit different depth requirements.

Water Level Detector & Warrick® Liquid Level Control System - Gems™ Sensors
The liquid level control system shown here is designed for “pump up” application. The pump will start refilling the vessel when the liquid reaches the lower probe tip, then stop refilling the vessel when the liquid reaches the higher probe tip.

 

Category::
Level
Sub-Category::

Warrick Conductivity Sensors

Warrick Conductivity Sensors Image

Warrick® Conductivity level control systems rely on the liquid level sensing capability of probes (electrodes) that are housed inside fittings designed to accommodate one or more probes. The concept is simple: take advantage of a liquid’s conductive properties to complete a circuit and cause a control relay to actuate. These single- or multi-point sensors have no moving parts and the stainless steel corrosion-resistant electrodes can be cut to the desired length. Multiple probes per fitting allow control of several functions in less space with less expense for equipment and installation. To create a system select from numerous level controls, fittings and probe options. For OEM’s we also have the capability to custom configure liquid level control sensors and electrode fittings to meet your specific conductivity level control application requirements.

Warrick® Liquid Level Controllers

For over 50 years Warrick® Controls have offered dependable no-moving-parts control and monitoring of conductive liquids. Now as part of the Gems™ Sensors family, Warrick® conductivity controls continue to offer reliability, process automation, labor savings, flexibility and operator safety at economical cost. The concept is simple: take advantage of a liquid’s conductive properties to complete a circuit and cause a control relay to actuate. Use of permanently-mounted stationary electrodes gives the user precise accuracy, repeatability and no-moving-parts reliability. This simple concept has led to the development of a complete line of conductivity-based liquid level detectors, water level detectors, and control units and electrode fittings shown here. For OEM’s we also have the capability to custom configure liquid level control units and electrode fittings to meet your specific application requirements.

System Components

  1. The liquid level control unit is an electrical device with contacts that open and close in response to liquid levels sensed by the probes. Because it is wired directly to the power source and to the sensing source, it can send signals that activate or de-activate solenoids, pumps, alarms or pressure switch devices. Warrick®controls are available in many different designs and sensitivity ratings for a wide range of application requirements.
  2. The fitting is a housing that holds the probes (or floats), insulates them from the vessel, and provides a means of connection to the control. Warrick® fittings are available for single-probe or multi-probe applications, for mounting to vessels in a variety of ways, and in open or pressure tight styles.
  3. The probe is a sensor that extends downward from the fitting, with the tip positioned precisely at the level where the control should be activated. Warrick® probes are available in a variety of materials to suit different liquids and a variety of lengths to fit different depth requirements.

Water Level Detector & Warrick® Liquid Level Control System - Gems™ Sensors
The liquid level control system shown here is designed for “pump up” application. The pump will start refilling the vessel when the liquid reaches the lower probe tip, then stop refilling the vessel when the liquid reaches the higher probe tip.