-
Land Instruments InternationalProviding temperature measurement solutions to industry since 1947 and combustion efficiency monitoring to power station begining in 1975 -
Process Control / Product QualityOptimising the quality of finished products by providing live temperature information to the process control system. -
Combustions & Emissions MonitoringOptimising combustion efficiency, minimising pollutant gas emissions, and monitoring these emissions to ensure compliance with local regulations. -
Asset ManagementContinuously monitoring temperatures and gases to maintain plant integrity, extend equipment lifetime, plan maintenance and reduce the risk of injury to personel.
Portable Sulphuric Acid Dewpoint Temperature Monitor
It is designed specifically for plant requiring only periodic monitoring of the sulphuric acid dewpoint temperature for boiler efficiency checks, corrosion protection and evaluation of the effectiveness of corrective measures such as fuel additives and changes in the combustion conditions.
Key Features
- Measure Sulphuric Acid Dewpoint Temperature – A unique but vital measurement
- Key process parameters measured and calculated – Essential operator information including SO3
- Easy to use precise control – Obtain a reading in minutes
- Weighs only 10kg (22lb) – Easily carried around plant
- Robust, industrial design – For daily use in the harshest plant environments
- Data logging – Capture and store over 10,000 readings
- Simple field maintenance – Easy-fit measurement cell – replace in minutes
- Traceable Calibration – To national standards in our own UKAS approved lab
Key Benefits
- Manage the use of high cost fuel additives such as MgO
- Monitor SO3 slip within an ESP to improve ash collection efficiency whilst minimising acid aerosol emissions
- Prevent Air Heater Fouling
- Reduce maintenance caused by cold-end corrosion in maintaining the exit gas above the dewpoint temperature
- Monitor acid aerosol emissions (H2SO4 / SO3)
- Monitor and reduce acid smut emissions
Cross Stack, In-Situ Carbon Monoxide Monitor
Key Benefits
- Direct continuous measurement of Carbon Monoxide
- True representative measurement – reading averaged across entire duct
- Improved combustion control and efficiency savings
- Low running and maintenance cost
- High reliability – robust design
- Simple installation – advanced alignment features
- Over 20 years of experience in carbon monoxide monitoring – 4th generation product
Lancom 200 – Portable Sulphuric Acid Dewpoint Temperature Monitor
It is designed specifically for plant requiring only periodic monitoring of the sulphuric acid dewpoint temperature for boiler efficiency checks, corrosion protection and evaluation of the effectiveness of corrective measures such as fuel additives and changes in the combustion conditions.
Key Features
- Measure Sulphuric Acid Dewpoint Temperature – A unique but vital measurement
- Key process parameters measured and calculated – Essential operator information including SO3
- Easy to use precise control – Obtain a reading in minutes
- Weighs only 10kg (22lb) – Easily carried around plant
- Robust, industrial design – For daily use in the harshest plant environments
- Data logging – Capture and store over 10,000 readings
- Simple field maintenance – Easy-fit measurement cell – replace in minutes
- Traceable Calibration – To national standards in our own UKAS approved lab
Key Benefits
- Manage the use of high cost fuel additives such as MgO
- Monitor SO3 slip within an ESP to improve ash collection efficiency whilst minimising acid aerosol emissions
- Prevent Air Heater Fouling
- Reduce maintenance caused by cold-end corrosion in maintaining the exit gas above the dewpoint temperature
- Monitor acid aerosol emissions (H2SO4 / SO3)
- Monitor and reduce acid smut emissions
CO & O2 Monitor
The FGA 900 series of combustion efficiency monitors use dual sensor technology to measure the levels of up to Carbon Monoxide (CO) and Oxygen (O2) in a single compact unit.
This range of gas analysers carry a wide range of compliance and performance approvals including those from the US-EPA, UK MCERTS and German TÜV.
Key Features
- Fully integrated system in a single compact box – no additional components required
- Suitable for a wide range of applications – up to 3 gases in a single analyser
- Simple installation – locate the analyser anywhere, including outside locations
- Automatic calibration option – for continuous unattended operation
Key Benefits
- Combustion efficiency measurement – for optimizing process efficiency where conditions are changing
- Low maintenance – straightforward servicing without specialist skills
- Proven high performance – dual sensor measurement technique, TÜV and MCerts approved/Certified to US EPA standards
Combining the unique features of three patented technologies, the 4200+ achieves the highest possible specification for the fundamental performance parameters for an opacity monitor, with no moving parts.
The Model 4200+ is a compact smoke, dust and particulate monitor for measuring dust emission concentrations on industrial processes and non-compliance applications. This dust monitor is ideally suited to multiprocess plants with common exhaust stacks.
Opacity and Dust Emissions Compliance Monitor
The Land Model 4500 MkIII has reset the industry standard on compliance opacity and dust concentration measurement. Combining the unique features of three patented technologies, the 4500 MkIII achieves the highest available specification for the principal performance parameters, as defined by the internationally recognized ASTM Standard D 6216-07.
Complies with QAL-1 and PS-1
Process and Non-Compliance Dust Emissions Monitor
The Model 4200 is a compact smoke, dust and particulate monitor for measuring dust emission concentrations on industrial processes and non-compliance applications. This dust monitor is ideally suited to multiprocess plants with common exhaust stacks.
Key Features
- Small, lightweight and compact
- High reliability, low maintenance
- Measurement Output in Opacity or mg/m3
- Wide range of optional accessories – failsafe shutters
- Simple keypad operation
Key Benefits
- Easy to locate and install
- No moving parts during measurement process
- Flexible configuration
- Configure the instrument with various accessories to meet process requirements
- Straightforward setup, calibration and diagnostics
Lancom 4 – Portable Combustion & Stack Emissions Gas Analyser
The Lancom 4 is a compact, portable combustion and emissions analyser for checking or testing a boiler system or pollutant process. Building on the success of the Lancom III, the Lancom 4 represents the next generation of portable gas analyser technology. It has the capability to monitor up to 9 different gases, and a total of 17 measurement parameters simultaneously. The Lancom 4 offers the best accuracy available from a portable gas analyser, achieved by using an advanced sample conditioning system.
- High Quality Colour Display – Visualise your data with widescreen display
- Multiple Language Support – Navigate the menu in English, French, German, Italian, Spanish and Chinese (other languages available upon request).
- USB Communications Support – Simple interface to PC and data transfer – supports USB Memory Sticks
- Setup and Measure in Minutes – Instant Readings – Simplicity is built into the Lancom 4 design. Switch on, connect the sample probe and instantly make real-time gas readings.
- Exceptional Battery Life – Made to Work All Day – Exceptional battery life is key to an exceptional portable gas analyser. The Lancom 4 has dual rechargeable batteries for up to 8 hours continuous use.
- Integral Sample Conditioning – High performance sample conditioning for high accuracy and repeatability. All in one portable box.
- Nine Simultaneous Gas Measurements – The Lancom 4 has the capacity and flexibility to meet all measurement requirements in a single instrument.
Gases Measured
- Carbon Monoxide (CO low range)
- Carbon Monoxide (CO high range)
- Carbon Monoxide (Hydrogen compensated)
- Oxygen (O2)
- Carbon Dioxide (CO2)
- Nitric Oxide (NO)
- Nitrogen Dioxide (NO2)
- Sulphur Dioxide (SO2)
- Hydrogen Sulphide (H2S)
- Hydrocarbons (CxHy)
- Nitric Oxides (NOx) – calculated where NO2 sensor not fitted
Key Benefits
- Up to 9 simultaneous gas measurements – user selectable
- Monitoring of up to 17 measurement parameters – one instrument to meet all requirements
- Weighs only 6 kg / 13 lb – easily carried around plant
- Robust, industrial design – for daily use in the harshest plant environments
- Wake and Sleep, semi-continuous operation mode – for periodic unattended operation
- Range of user selectable options – ideally matched to application requirements
- Data acquisition & analysis software – useful tool to observe trends
- Simple field upgrade – add features and options as and when required
- Meets US EPA CTM 034 reference method – report generation to recognized standards
Continuous Efficiency Monitors
Dust & Opacity Compliance Monitors
Portable Gas Analyzers